Aluminum wrap
Metal wrap can be added over new or sound fascia once any rot is gone.
Exterior Services
Fascia Repair Cranford, NJ
A roofing contractor in Cranford can fix soft, split or loose fascia along the roof edge, whether it is painted wood, PVC or wrapped in aluminum, so the gutters have solid wood to hang from again. One call to (908) 562-6887 reaches a nearby roofer who handles fascia repair.
When a fascia board goes soft, the cause is almost always water running down the back of the gutter instead of into it. Clogged or poorly pitched gutters spill over the back, and a roof edge with no drip edge sends water straight down the fascia. The wood slowly loses strength until the gutter spikes or hanger screws no longer hold.
Rotted fascia is often the visible part of a bigger problem. Left alone, the rot moves into the rafter ends and the edge of the roof deck, which turns a trim repair into structural work. On homes with metal fascia wrap, the rot often goes unseen until the gutter falls.
It helps to know what you are seeing before you call. Write down which sides of the house show peeling paint, gaps or a sagging gutter. Mention whether the fascia is painted wood, PVC or covered in aluminum, and how old the gutters are.
Depending on what the roofer finds, fascia repair in Cranford, NJ can go hand in hand with soffit repair and gutter installation.
Need fascia repair in Cranford? Call (908) 562-6887 to reach a nearby roofing contractor.
Call nowThe process
How fascia repair works
A fascia repair only lasts if the water that rotted it is redirected.
Inspect the roof edge
The roofer checks the drip edge, the first course of shingles, the gutter pitch and the downspouts above the damaged fascia. The length of the damage decides how much board is replaced.
Free the board
To reach the fascia, the gutter over it is removed and the hangers pulled. This is a good time to check the gutter itself for leaks and bad seams.
Repair the framing
The roofer looks at the rafter ends and the sub-fascia, since soft framing will not hold a new board. Skipping it is the most common reason fascia fails twice.
Install new fascia
The new board is fastened to the rafter tails with corrosion-resistant nails or screws, with tight joints at the corners. End grain is sealed so it does not soak up water.
Close the gap
A drip edge is added or reset so it laps over the back of the gutter and throws water clear of the fascia. Without it, the same board will rot again.
Finish the edge
Gutters are rehung on the new fascia with a slight slope toward the outlets. The finished edge is checked with a hose or after the next rain.
What is included
What fascia repair covers
Rafter tail repair
Rafter tails damaged by water are repaired before the fascia goes back on.
Rotted board repair
Damaged fascia is replaced with primed wood or PVC and scarfed into the existing board.
Edge flashing
New drip edge is tucked under the shingles over the gutter which stops the rot from coming back.
Gutter rehanging
Loose gutters are refastened and pitched toward downspouts with screws instead of loose spikes.
Related service
Fascia Board Replacement Cranford, NJ
Fascia board replacement means taking off whole lengths of board rather than patching short sections. With the old fascia off, every rafter end can be checked and repaired before the new boards are fastened. It is also the moment to choose a material, whether primed wood, PVC, composite or wood with an aluminum wrap.
In Cranford, fascia board replacement often lines up with a new roof or new gutters, since the roof edge is already being worked on. Make sure rotted boards are removed, not covered. The new boards should match the old width so the soffit closes properly.
Related service
Fascia Board Repair Cranford, NJ
Fascia board repair handles damage that is limited to a few spots, such as a rotted corner, the area under a leaky gutter seam or a section by a downspout. Angled joints hold paint and shed water better than straight cuts, so they are the standard for patch repairs. For a shallow soft spot, an epoxy consolidant and filler can restore the surface without cutting the board.
Patching a fascia board in Cranford without fixing the gutter or drip edge above it just buys a season or two. That usually means resealing a gutter seam, unclogging a downspout or adding drip edge over the repaired section. Sealed and painted, the patch holds up like the original wood.
Local help
Fascia Repair Near Me
In Cranford, fascia tends to fail first on the sides of the house where gutters clog fastest. Homes in Cranford and nearby towns like Garwood, Westfield, Kenilworth and Roselle Park range from older houses with wood fascia that needs regular paint to newer builds where metal wrap can hide rot underneath, and replacing a short section early is far easier than rebuilding the roof edge later.
Need fascia repair around Cranford? Call (908) 562-6887 for a Cranford roofer who serves the towns around it too.
How the weather here affects roofs around Cranford
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, which is how ice dams form and back water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. Most homeowners in Cranford, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why not wait
Drier ceilings
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Familiar with local homes
Local roofers see the same roofs and storm damage across Cranford and nearby towns.
Straight answers
Ask the roofer about the cause, the options and the estimate before work starts.
Fascia Repair questions
Why do gutters pull away from the fascia?
Gutters hang from the fascia, so their strength depends on it. Soft fascia lets the fasteners work loose, which is often the first sign of rot. The fix is solid wood plus new hangers, pitched toward the downspout.
Is it safe to wrap rotted fascia in aluminum?
Wrapping over soft fascia traps moisture and lets the rot continue unseen. Gutter screws go through the wrap into the rotting board and gradually pull loose. Wrap is a good finish over new or solid fascia.
What causes fascia boards to rot?
Most fascia rot traces back to the roof edge and the gutters. Overflowing gutters, gutters pitched the wrong way and roof edges without drip edge soak the board repeatedly. Bare end grain and failed paint let water soak in faster.
Do I need new fascia boards or just a repair?
Repair is fine when damage is limited to a few spots and the rafter tails are sound. If the damage is widespread, new boards end up being the simpler fix. Either way, the rafter tails behind the board need to be checked.
Which fascia material lasts longest?
Rot-proof materials such as PVC and composite last longest. Wood looks traditional and is easy to work with, though it needs upkeep. No material holds up if water keeps running behind the gutter.
More questions? Call (908) 562-6887
Often needed together
Soffit Repair
Fixing damaged soffits, blocked soffit vents and gaps where animals get in, so the attic breathes and the overhang stays sealed.
Learn moreGutter Installation
Gutter installation that carries roof water away from the siding, fascia and foundation, from K-style aluminum to half-round and copper.
Learn moreGutter Repair
Repairs for leaky joints, bad pitch, loose hangers and damaged downspouts, before the leaks rot the fascia behind them.
Learn moreRoof Repair
Repairs for missing shingles, lifted tabs, cracked pipe boots, loose flashing and soft decking, without replacing a roof that still has life left.
Learn more
Looking for something else?
See all roofing servicesNeed fascia repair in Cranford, NJ?
Call (908) 562-6887 for a local roofer in Cranford and nearby towns.